Engine Repair Parts & Accessories

Tiny Tach and Hour Meter

install in less than 30 seconds

How can you know what the problem is when everything revolves around engine rpm? We spend countless hours each week trying to help customers repair their equipment. Without a tachometer all we can do is guess at what the problems may be. Please help us help you by installing a Tiny Tach on your engine. It only takes about 30 seconds.

This meter provides a read out of the engine speed while the equipment is running. When the equipment is off it shows the hours of operation. The hours can be reset. This works great because when scheduled engine maintenance is performed every 100 hours, the meter can be set to zero to start counting the next 100 hours. A record of the engine total lifetime hours of use is also valuable.

Part #: 1429
for Single and V-Twin Engines

Each $59.97

Part #: 1429EFI
for Kohler EFI Engines

Each $75.97

EZ OIL DRAIN VALVE

…also work great with Pumps and Gear Reducers

No more ‘messy’ oil changes!

Premature engine failure is most likely because changing the oil is seldom performed simply because it is a messy job. With the quick drain plug you no longer have to clean your equipment after oil changes.

Note: It is much easier to change engine oil when the engine is hot.

FITS ALL ENGINES WITH 3/8 NPT

Part# 1428EZ

Each $25.99

Part #: 1428EZL

Each $27.97

Quick Change Oil Drain for KOHLER 14 and Honda

Includes: Engine adapter, steel braid dump hose and 3/8″ plug that can be removed to drain oil. You can also use the optional #1428 (shown) or #1428EZ valve in place of the plug.

Part #: 1428H

Each $27.49

Engine Idle Down

When the Trigger Gun is released the Engine returns to idle.

• 3/8” Conical Connection • 320° F Max.
• Adj. stroke .28-.55” • 40” Cable
• Returns to Idle when pump
drops to 290 PSI

General Pump ZSPEED 3600 PSI

Click here for ZSpeed installation instructions

Part #: TC5800 – Premium 5800 PSI

Each $56.97

Part #: 2901 – General Pump 3600 PSI

Each $107.00

Throttle Cable

For precise RPM adjusting

This cable is used to remote mount the engine throttle when getting in and out of a high box truck to idle down the engine is difficult. By turning the dial you can really ‘tweak’ the rpm’s to the precise speed that you need. This would be a great feature for contractors who use the customer’s water supply and find themselves in a situation where the supply will not keep up with the engine/pumps requirements. By dialing down the rpms’s the pump will be using less water.

Part #: 1991

Each $57.19

1/4″ Inch Square Key Stock

For mounting pulleys, bushings and gear drives to the engine shaft

1/4 Inch Square Key Stock

Part # 3777 – 1 Inch Long Keyway

Each $3.29

Part # 3777A – 2 1/4 Inch Long Keyway

Each $4.25

Cut to size with the foot long Keyway

Part # 3777B – 12 Inch Long Keyway

Each $16.67

EnviroSpec Engine Terminator

This 12 volt pump saver kills the engine if the pump head overheats to 145 degrees. So the next time your employee leaves the machine running in by-pass to long your pump will not be damaged. Installs on the spare inlet side of the pump. Connect one wire to ground and the other to the low oil shut down. DC Only.

Part #1990

Each $21.00

Replacement Starter Solenoid

Fits most gas engines
found on pressure washers.

Part #1427

Each $19.47

Fuel Medic

Ethanol is killing your engine!

When the government mandated the addition of ethanol into gasoline it brought with it a problem that left professionals who use small engines fighting to keep their equipment running. Ethanol produces water when left in a gas tank for a short period of time. Fuel Medic frees up and removes the water.

Enough for to treat 125 gallons!